Community Apps

This package contains the NCT6687 Drivers and installs them for using it with the Dynamix System Temperature Plugin.

This plugin will install all necessary modules and dependencies for your Nvidia Graphics Card so that you can make use of it in your Docker containers. In the settings/plugins menu you find your UUID of your graphics card(s). You can also choose your preferred version of the Nvidia drivers, by default it will always grab the latest driver version that is availabe for the current Unraid build. This plugin satisfies installation prerequisites of the GPU Statistics plugin from Community Apps. With both plugins installed you can display Nvidia GPU utilization on the unRAID Dashboard. ATTENTION: If you plan to pass through your card to a VM don't install this plugin!

This plugin will install all necessary modules and dependencies for your Nvidia Graphics Card so that you can make use of it in your Docker containers. In the settings/plugins menu you find your UUID of your graphics card(s). You can also choose your preferred version of the Nvidia drivers, by default it will always grab the latest driver version that is availabe for the current Unraid build. This plugin satisfies installation prerequisites of the GPU Statistics plugin from Community Apps. With both plugins installed you can display Nvidia GPU utilization on the unRAID Dashboard. ATTENTION: If you plan to pass through your card to a VM don't install this plugin!

OpenFAN is open-source, open-hardware 12V PWM fan controller for the hobbyists and hackers! This fan controller allows you to control 10 PWM fans over USB or remotely over network. OpenFAN gives you two ways to control each fan: Traditional (PWM): Set target PWM and the fan will spin at whatever RPM it is designed to spin with that PWM. (ie. Assuming 2000RPM fan, if we set the PWM to 50%, the fan should spin at 1000RPM which is half of full speed) Advanced (RPM): Set target RPM and OpenFAN will use it's built in PID algorithm to keep the fan always spinning at that RPM. OpenFAN also has an open-source API that allows you to programmatically control your fans, set custom profiles and more. OpenFAN was designed by PC enthusiast for PC enthusiasts. Key features: - Works on Windows, Linux and Mac - 10x PWM fans (Supports 12V, 4-pin fans) - Individually control each fan - SATA power (cable not provided) - Micro-USB communication (motherboard cable included) - Control fans by setting target PWM or target RPM - Optional I2C/1-Wire (header not populated) - Open source API for communication and control - Open source and open-hardware design - Control fans over USB or remotely over network* - FanControl integration through plugin To control fans remotely over network, the OpenFAN board needs to be connected to the PC via USB and running the OpenFAN software. The software allows you to access the fan controller remotely over network.

This package contains and installs the OpenRGB Patch that needs to be installed in conjunction with the OpenRGB Docker container to take full controll over your RGB lighting. To see all the RGB devices you have to pass through the devices /sys/bus/i2c/device and /dev/i2c-0 to the OpenRGB Docker container and maybe all other /dev/i2c-X devices (where you have to replace X with the number from the device to pass through).

This package contains and installs the QNAP Embedded Controller chip Kernel module, this allows you to read fan speeds and temperatures as well as reading and writing the fan PWM values from the ITE Tech Inc. IT8528 embedded controller chip. Currently known supported units are: TS-473A, TS-673A, TS-873A, TS-h886, TS-453Be, TS-877, TS-1677x, TS-253B, TS-453A, TS-464 Source: https://github.com/Stonyx/QNAP-EC

This package contains the Realtek OOT Drivers and installs them, a reboot is required after installing the plugin (upgrading to a newer Unraid version maybe needs a second reboot too). The following Chipsets are supported by this driver: Network Interface Controllers > 2.5G Gigabit Ethernet > PCI Express RTL8125 / RTL8125B(S)(G) Source: https://github.com/jinlife/unraid-r8125-r8152-driver

This package contains the Realtek OOT Drivers and installs them, a reboot is required after installing the plugin (upgrading to a newer Unraid version maybe needs a second reboot too). The following Chipsets are supported by this driver: Network Interface Controllers > 5G Gigabit Ethernet > PCI Express RTL8126 Source: https://github.com/jinlife/unraid-r8125-r8152-driver

This package contains the Realtek OOT Drivers and installs them, a reboot is required after installing the plugin (upgrading to a newer Unraid version maybe needs a second reboot too). ATTENTION: To utilize 2.5Gbit/s speeds you have to add this line at the bottom to your 'go' file: 'ethtool -s eth0 autoneg on advertise 0x80000000002f' (without quotes and modify eth0 to the corresponding adapter in your system)! To utilize 5Gbit/s speeds you have to add this line at the bottom to your 'go' file: 'ethtool -s eth0 autoneg on advertise 0x180000000002f' The following Chipsets are supported by this driver: Network Interface Controllers > 5G Gigabit Ethernet > USB 3.0 RTL8157 Network Interface Controllers > 2.5G Gigabit Ethernet > USB 3.0 RTL8156 / RTL8156B Network Interface Controllers > 10/100/1000M Gigabit Ethernet > USB 3.0 RTL8153 / RTL8153B / RTL8153C / RTL8153D / RTL8153E Network Interface Controllers > 10/100/1000M Gigabit Ethernet > USB 2.0 RTL8154 / RTL8154B Network Interface Controllers > 10/100M Fast Ethernet > USB 2.0 RTL8152B Source: https://github.com/jinlife/unraid-r8125-r8152-driver

This package contains the Realtek OOT Drivers and installs them, a reboot is required after installing the plugin (upgrading to a newer Unraid version maybe needs a second reboot too). The following Chipsets are supported by this driver: Network Interface Controllers > 10/100/1000M Gigabit Ethernet > PCI Express RTL8111B/RTL8111C/RTL8111D/RTL8111E/RTL8111F/RTL8111G(S)/RTL8111H(S)//RTL8118(A)(S)/RTL8119i/RTL8111L/RTL8111K RTL8168B/RTL8168E/RTL8168H RTL8111DP/RTL8111EP/RTL8111FP RTL8411/RTL8411B Source: https://github.com/jinlife/unraid-r8125-r8152-driver

Spin down idle SAS drives the same way SATA drives are spun down. If you have SAS spinning drives in your array, you may have noticed that Unraid, while asserting that they have been spun down, does not in fact spin them down (true at least up until version 6.8.3). This plugin attempts to ensure that SAS drives spin down and up in sync with Unraid schedule (i.e. same as SATA drives).

scanservjs is a web UI frontend for your scanner. You can perform scans using your USB or network scanner through this web UI. The application allows you to share one or more scanners (using SANE) on a network without the need for drivers or complicated installation. To discover your devices, open the docker console and run: scanimage -L This will return a list of discovered devices. Copy the device id e.g. "epson2:libusb:001:002" and put it into the devices variable.

A plugin for advanced users installing SnapRAID onto UNRAID systems, now with support for multiple arrays.

Provides GUI for BTRFS Snapshots.

This Plugin will install the Sundtek DVB Drivers to Unraid. Please visit the Plugin page after installing the plugin to configure your TVHeadend instance for use with this plugin.

Reads Tasmota power devices

This package contains the UGREEN LED Driver which will allow you to get your LEDs to work on your UGREEN NAS (please note that not all models are supported). The plugin is based on: https://github.com/miskcoo/ugreen_dx4600_leds_controller

This Plugin adds uinput to unRAID.

Provides GUI for USB Devices. Additional support via addon plugin for USB over IP. Addon plugin install button available via the settings page following enabling USBIP.

Install Modules for GSM Modems. Modules: options and usb_wwan.

Install Modules for aqc111 based USB Network Adapters. Modules: AQC111.

Install Binaries for usbip and usbipd with associated libraries.

This plugin allows you to perform actions with Wakeonlan packets.